Recent content by Joker2

$3,500 firm 1975 Wellcraft V20, runs great, looking to get a bigger boat. I had a lot done to this boat in the 6 years I had her. - New transom, completely rebuilt 1995 Evinrude 150HP Ocean Pro ( both done 4 yrs. ago ) motor has 50-75 hrs. runs great. - Repainted entire hull - SS cleats all...

$3,500 firm 1975 Wellcraft V20, runs great, looking to get a bigger boat. I had a lot done to this boat in the 6 years I had her. - New transom, completely rebuilt 1995 Evinrude 150HP Ocean Pro ( both done 4 yrs. ago ) motor has 50-75 hrs. runs great. - Repainted entire hull - SS cleats all...

Are there any other boat manufacturers who's bow rail will fit a 75' V20?

Are there any other boat manufacturers who's bow rail will fit a 75' V20?

I have a 75 v20 with 20 gall. saddle tanks, I am getting water in my fuel vent in rough conditions. any suggestions on how to correct the problem. FYI when I redid my tanks I mounted vents with the screens facing down. i did not put a clamshell cover, should I have?

Can anyone recommend a good roller arm spacing for the 75' 20 I just bought a venture single axle trailer and the spacing of the rollers port to starboard no matter how i slide the bracket doesn't seem to work with the location of the strakes. Rollers are 14 - 1/2" center to center. The trailer...

I recently purchased a used trailer and I had to move some rollers around because they were sitting under the strakes, I am not totally comfortable with the setup. I was told it had a 21' boat on it, it seems too small, the back of my boat hangs off 23"" past the last roller. I had read there is...

Wondering how much a stator would be for a 1994' 150 HP Evinrude Ocean Pro? Thanks:head:

I was wondering if anyone knows about how much it would cost to have my engine tore down to determine a chatter I have had in my engine ( sounds like a lifter tap on a car ) Engine was only rebuilt three seasons ago, I suspect that my VRO was not supplying proper oil for two seasons, finally...

Hey guys I recently got rid of my VRO tank and went to mixing oil into the gas. Everything is fine except when I go to use the boat after e few days to a week of not using it, it is hard to start the first time. It takes about 10-15 cranks to get it going, when it starts there is a fair amount...

Spoke to my mechanic, told him I have a rattling noise only between 3,000 - 4,000 RPM's he told me to add oil to my gas 50:1 just to see if the rattling noise goes away ( in case VRO isn't working ), then check to see if there is water in the lower unit oil. If not then he will look at it. ( I...

Any reviews on a Mark-4 Chartplotter/Fishfinder ?

I was wondering any opinions on two things. How does this gas consumption sound -- 20 minutes (no wake) each way in and out of channel, 3 hrs nonstop tubing with 5 kids 2 adults, food, drinks, ( got 5400 RPM's ) gear put in 11 gallons before trip 89 octane. Fuel gauges were right back where I...

I purchased a new prop Michigan wheel vortex ,it came with a hub kit, when I went to change the prop, I put it all together and the washer that goes on after the prop ( the one that is about 3/8" thick and has grooves to interlock with the splines ) doesn't catch any splines. The splines end...

Hey guys i had a thought about my RPM problem, ( only getting 4500 ) I have been through all the checks in the past 1-1/2 years, when I did my new transom ( 2 Yrs. ago ) I replaced all fuel lines and added a water seperator, I used 5/16 lines, someone mentioned to me they really should be 3/8...