Search results

I have a question for the experts. I have an engine that I'm selling and this is what it looks like. It's a 1989. Would it scare you off?

I have a pair of Garelick seats for sale. They're in good shape but have no cushions. I'm asking $100 OBO for the pair. Thanks

Went out today out of Atlantic Highland Municipal Harbor. It was my third trip out on my own boat since Sandy. It was a nice day, minus the am rain and the need to break in my lower unit. I never realized how slow 3500 rpm actually is. Managed it put about 3 hrs on the boat and 3 keepers to 5...

I have a 1989 evinrude 110 hp 20" shaft for sale. The VRO system was disabled. The compression was even when I checked it a few months ago, I don't have the numbers handy of course. The lower unit and water pump were replaced in 2012 and the engine was barely used since. It's currently in my...

What's the best way to measure shift rod height on a 98 Johnson lower unit? The PO had an SEI lower unit installed on my 22WA a few years before I bought it. When I changed the gear oil I noticed a lot of metal so I sent it to them. They said the reverse clutch was shot and they replaced pretty...

I was at MI today with my wife and daughter and I saw a nice V20 drifting on the PT Pleasant side. It was an IO with a light blue hull. Looked really clean and I was wondering if it was anyone from the site. It was one of the cleanest V's that I've seen in person. Looked like it may have been...

My 99 22WA has a 98 Johnson 200 v6 with an SEI lower unit on it. I had to send it back to them because I found some large metal shavings and felt a bit of a vibration. I have a 96 130 v4 that has the v6 style lower on it. On the outside they're identical. I know the gear ratio is different...

I have a 98 Johnson Ocean runner on my boat that I purchased at the end of last season. I did a compression test and it was 100 across the board. I ran the boat twice last year and it ran well. I just finished going through the boat and fixing a lot of little issues with it so I haven't run it...

The original fuse panel is full on my 22WA. I have a blue seas fuse panel that I took off my Striper and I was wondering what size wire to use. I was thinking 10 or 8 gauge. I didn't want to just jump off the other one either.

I've got an 05 GMC Sierra 1500 4wd with an autotrac transfer case and I believe a 4L60e trans. I've owned it since new. I have 91000 miles on it now. I changed the trans fluid at 50k and 75k, according to GM's guidelines. I've been using a hyper tech programmer since 06. I've been thinking of...

I have some rear brake parts for a 4-cyl Dodge Caravan. They're new aftermarket parts that I purchased for my grandfather but his van was totaled in Sandy, so I've been sitting on them for a while. I have two drums, shoes and a spring kit. I'd like $60 OBO. You can email me through here if...

I have an 82 Grady White Tarpon(tournament) 190. I pulled the 89 110 V4 to put my 96 Johnson on to test it out. When I removed it I decided to pull the aluminum trim and take a look at the transom. I wasn't happy to see that it was a wet and seemed to be rotten. I saw someone on here mentioned...

Boat railing hardware I have some bow rail hardware. I have 6 60 degree round bases and 6 60 degree rail fittings. They are chrome plated zinc. The brand is Sea Dog and they are new in box except a few of the hand rail fittings that fell out of their boxes. I decided to remove the bow rail on my...

The tach on my Grady wasn't working. I'm in the middle of doing some repairs so I can't check the signal from the engine. I tried to put voltage from a jumper pack to it but it didn't do anything. I tried the same thing with a known good tach that had a broken face and had the same result...

On my 22WA the PO put the fuel and water separator under the port bait well in the stern right next to the livewell/washdown pump. The pump was rotted and a wire broken off and the separator was dripping, not a good combo. On my Striper it was mounted in the splash well. I like the cleaner look...

I've got a 96 Johnson 130hp engine that was on my Striper. During Sandy my boat was in AHMM, on land, and was partially submerged. My boat was smashed up against a concrete filled steel pole repeatedly. The cowling on the outboard was smashed, the starter was damaged,and some water got on the...

I've been lurking on this board for a while but haven't posted yet. I originally joined when I was looking for a boat and was planning on picking up a V20 as I previously owned an 89 18 Sport and loved the boat. Well I wound up getting an 82 Grady 190 Tarpon but then a 99 Wellcraft 22 WA fell...