Search results

Good morning, Hope all is well, Looking for information on carburetor part numbers for a evinrude E225cxeud. I am told 0439188 and 0439189 will work ? I find these number on boat.net website. part numbers I have 0437326 for carb, 0437326 for float chamber 0438515 for upper Throttle body...

well, as i was installing my Lenco trim tabs, to the transom of my 86 v20 cc, brown water came out of the drill holes. When i purchased the boat i did check for flexing on the transom, and when i removed all the hardware from the swim platform, engine mounting bolts, i didn't noticed any rot...

hello I am installing a telestar hyd steering for my 86 v20 with a Evinrude 225. I notice the helm pump requires a smaller hole (3 in) and has a four bolt pattern. (PHOTOS INCLUDED) I was wondering if anyone has ever installed one and still had the 20 deg angle the black cover provides. thanks...

hello i was wondering if anyone knows for sure if the floorboard area in front of the drain hole in the bilge area is suitable for screwing down a bilge pump. it feels solid, but i want to make sure. i had a piece of starboard secured down with 5200 and it keeps coming off no matter how i clean...

i replaced the plywood under the lids with 3/4 in marine plywood, and fiberglass it with 1.5 matted fiberglass. followed by a layer of 1078. my question is should it be just painted or a gelcoat layer brushed on? any advice would be appreciated. jet,

HI, i was wondering if anyone here has used a Deutsch connector and what did they use for a crimping tool? The vendor wants $300.00 for the crimper and i really dont want to pay that much if someone has a better and cheaper way. jet.

Hello, I read an article in boating magazine a few years ago, Stating not to install a check valve after the bilge pump. In a recent article this year they show a check valve install. Like any one opinion on that. I'm getting ready to install two new pumps with new lines on my boat. Jet

hi just finished cold taring my original 60 g. factory fuel tank. (photo enclosed). I was going to powder coated it, but when i called RDS aluminum, they said cold tar epoxy is a better choice. I will install starboard panel strips, with 3m 5200, around the fuel tank. staying away from anything...

Hi, working on my 86 v20 instrument panel, (picture enclosed) i have a evinrude 225 was wondering where can i install a sensor at? i still have both left and right bank, evinrude water temp.sensors from the factory installed. i was thinking of installing the sensor between the left and right...

Has anyone ever used Haysite plastic for support on the fuel tanks. a marine surveyor suggested this material. THANKS Jet

well here are some photos of my 60 gal fuel tank removal, on my 86 v20 c/c. i drained fuel, filled with water to remove gas vapors,let it fill for a while, left water in tank and with a pneumatic wheel cutter cut a slot, large enough to fit a steel bar inside tank, well that didnt work, it was...

Hello everyone I have a 97 Evinrude 225, going on a 86 v20 c/c, and I wish to use the factory systems monitor gage. Does anyone who has this system installed? Do you have it spliced into the regular instruments also? Thanks for the help.

Hello I have a 86 v20 c/c, and tomorrow I will be looking at a 96 Evinrude 225. I read some of the reviews here under the search. The engine I read is reliable and easy to maintain, but a gas guzzlers. What I'm looking for is what should the compression readings be? I read no more than 5%...

does any one know how to remove the wooden trim on the helm wheel? i dont want to break it thanks jet

well i got that 85 Johnson seized 150 engine torn apart. i had to cut off the exhaust housing with a cutting wheel to separate it from the block. i split the case and removed the pistons and rods. i enclosed a few pictures. i didn't think a seized engine would come apart so easily. jet

anyone knows why the ABYC does not recommend this fitting for below waterline fitting http://www.perko.com/images/catalog/product/xl/Fig%200333.jpg I'm replacing all my bilge pump thru hull fittings with s/s and the below water fittings with the above item along with the scupper item below...

HI I am looking for a vender in that can make a dashboard for my 86 V20 C/C. I still have the old panel but its very brittle, and will be installing new instruments and circuit breaker/switch panel. jet.:train:

I have a new 60 gal factory tank to install. I don't want to use any foam so is there any ideals on how to reinstall this tank I was thinking of metal straps with 1x2 wood strips under the straps (like the way it way installed) secured to the side stringers. This for the top, but looking for...

i was able to get a copy of the fuel tank spec from RDS ALUMN. in Perry Fl. they were an orginal mfg of below deck fuel tanks.

i was lucky enough that Mr. Sam Osteen from RDS Alum. for sending me the spec. on the orginal factory fuel tank. but i cant load it here because its too big so if any one wants it please PM me. jet:nice: