Search results

Anyone running an Evinrude Ficht that may have had a similar problem? I have a 2004 150HP Ficht with approximately 75 hrs that has a severe hesitation between 2000-3000 RPMs. Feels like it is going to stall. It is flawless below 2000 and above 3000. The dealer had replaced the fuel pump and...

Well to make a long story short, I had all sorts of fuel water issues last season, so I replaced the tank, vent, hoses, etc. My question is regarding the Racor filter. Should there always be gas in the see-through bowl? It is always full but I empty it and it seems to be just gas. Seems like...

http://capecod.craigslist.org/boa/1196651084.html

http://capecod.craigslist.org/boa/902975729.html

Seems clean and cheap http://capecod.craigslist.org/boa/625060690.html

Looks clean, but no detail on motor: http://boston.craigslist.org/gbs/boa/566461579.html

If you all remember, I decided to fix up my "V" that sunk June 06. After hours and hours of labor and lots of dollars on new power, I figured I would provide some "before after pics" of the '88 "V". Console Before Console After Motor Before Motor After :Note the bracket and temporary fill...

Not to sound "girly", but I would really like to get the fiberglass shine back on my 88. Oxidation is fairly bad, especially topside. I don't want to cover it up with a polish, but rather compound, sand and wax. So I am looking for suggestions on the steps and materials to use. I have a new...

MJ, Here's another i/o for you to convert. Anyone seen this one before? Not much detail. http://capecod.craigslist.org/boa/353941699.html

http://capecod.craigslist.org/boa/318395047.html

Anyone seen this one yet? Looks real clean: http://philadelphia.craigslist.org/boa/313578989.html

http://boston.craigslist.org/gbs/boa/303987222.html This boat looks familiar.

Anyone got a good recommendation for electrical parts? West Marine and Boatersworld are pretty high. I did not find anything on Flounder Pounder and I cannot wait for that Western Canada place.. The next phase of my recovery is rewiring and all my toggles are gone.

I am looking for recommendations on basic powertools required for fiberglass repair. I realize I need some type of dual action sander, but I do not have my own pneumatic compressor (but I can borrow when necessary). Can I get away with a corder Ranom Orbit sander to do both heavy work and...

I realize that windshields are hard to come by, but I have an 88 that I am repairing and I just spent a small fortune on repowering. Anyone out there willing to part with one. The rough measurements are 84 across (30x24x30) and 53" on the sides. The offset is 4 inches from the corner to the...

OK, so I finally got some pics of my project boat, which was not a project until it sank last year. I just ordered a 2004 Evinrude Ficht 150 with <50 hrs and a 7 year warranty. This is the back with the damaged bench and engine. This is a view of the missing windshield, no cabin door and the...

Would anyone with access to there V20 care to tell me the exact windshield measurements? I am on a relentless Internet search and do not have access to my boat. Any year from 78-89 would do. Very Much appreciation in advance.

http://boston.craigslist.org/nos/boa/296148911.html Not sure of the year but looks like mid 80's.

Here's another overpriced V20 being sold in MA. I love these boats too, but this is a ridiculous price. http://boston.craigslist.org/sob/boa/294713587.html

Saw this ad from Cape Cod while searching for a windshield for my 88. http://capecod.craigslist.org/boa/293371957.html